For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
-
ryanandcharl
- Full Member
- Posts: 36
- Joined: Fri Jan 13, 2023 7:35 pm
- Has thanked: 3 times
Post
by ryanandcharl » Tue Jan 31, 2023 8:32 pm
GENTLEMEN SHE LIVES! .. just about anyway haha
So it starts and idles for the first time in a very long time,
HOWEVER…
it’s struggling, idle was around the 200ish mark and wouldn’t respond to throttle very well.
Would I be right in suggesting a little tinker with the timing?
Thanks again all, should have just listened to everyone shouting “dissy! Dissy!” These past few months
-
Micron
- Site Admin
- Posts: 3208
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 53 times
- Been thanked: 86 times
Post
by Micron » Tue Jan 31, 2023 8:43 pm
We have all been there, myself included, but we might be a small bunch but we do know our onions and Ford Probe’s
Admin and Owner of this fine club
-
cpt black
- Tech Rep
- Posts: 2712
- Joined: Fri Sep 07, 2018 8:28 am
- Has thanked: 13 times
- Been thanked: 85 times
Post
by cpt black » Tue Jan 31, 2023 9:28 pm
Good news,when running and warm you can move the dissy (SLACKEN BOLTS) to lower the rev,s
if no strobe Light to get the idle down 650 /.750
-
ryanandcharl
- Full Member
- Posts: 36
- Joined: Fri Jan 13, 2023 7:35 pm
- Has thanked: 3 times
Post
by ryanandcharl » Wed Feb 01, 2023 9:45 pm
Ok so following on from yesterday I’m still getting trouble from the distributor. My issue is definitely timing as I’ve got spark but unburnt fuel in the plugs. As said I’ve had the engine running (best was weak with a low 200-300rpm). I’ve put the engine to TDC on compression stroke and faced the dissy arm to spark plug one, even moved the dissy body clockwise/ACW just incase. So why is my timing still off?
-
ryanandcharl
- Full Member
- Posts: 36
- Joined: Fri Jan 13, 2023 7:35 pm
- Has thanked: 3 times
Post
by ryanandcharl » Thu Feb 02, 2023 11:47 am
cpt black wrote: ↑Thu Feb 02, 2023 11:44 am
Have you pulled any codes on the diag box yet
Kev
The lightbulb trick from the diag box? did this before sorting the moby bypass and no codes shown. I’ll give it a go now that’s been done
-
ryanandcharl
- Full Member
- Posts: 36
- Joined: Fri Jan 13, 2023 7:35 pm
- Has thanked: 3 times
Post
by ryanandcharl » Thu Feb 02, 2023 3:22 pm
cpt black wrote: ↑Thu Feb 02, 2023 11:44 am
Have you pulled any codes on the diag box yet
Kev
I have a code this time, cleared and it returned.
It’s one long flash (starting/powering up)
Followed by 3 pluses after another, continuous. So as below
1 111 111 111 111 and so on
Thinking it’s the 03 camshaft sensor, but that being in the dissy and the dissy being new how could that be?
Last edited by
ryanandcharl on Thu Feb 02, 2023 10:02 pm, edited 1 time in total.
-
cpt black
- Tech Rep
- Posts: 2712
- Joined: Fri Sep 07, 2018 8:28 am
- Has thanked: 13 times
- Been thanked: 85 times
Post
by cpt black » Thu Feb 02, 2023 4:33 pm
Cold well be a Knackered Dissy even thou new,if you have your old one replace
and check the codes again,did you get the right coded dissy S1/S3
-
ryanandcharl
- Full Member
- Posts: 36
- Joined: Fri Jan 13, 2023 7:35 pm
- Has thanked: 3 times
Post
by ryanandcharl » Sat Feb 04, 2023 4:04 pm
cpt black wrote: ↑Sat Feb 04, 2023 3:32 pm
Any Updates
Updates
I’ve been on the phone to a helpful gentleman from ignition car parts LTD who’s swears they’re keeping most if not all of the UK Probes on the road
I’ve sent both my new and old dissy to them for a bench test and repair (might as well have a spare).
As the new one is pulling a cam sensor code I’m hoping its a quick fix, return and the car will run again. I’m thinking I blew the new dissy on starting the car without a moby bypass.
Will further update when it’s arrived
Who is online
Users browsing this forum: Google [Bot] and 36 guests
