Check engine light on solid

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
MikeyG
Full Member
Posts: 93
Joined: Thu Nov 29, 2018 6:01 pm
Has thanked: 1 time

Check engine light on solid

Post by MikeyG » Fri Sep 20, 2019 10:08 pm

Hey guys,

1995 2.0l.

Just tried the immobilizer bypass and think it worked fine. Kinda. Anyway the check engine light is on solid now and the car turns over but doesn't start. I put the immobilizer back on and it works as it should - I really dont think thats what caused the problem.

I cant read the check engine codes - I've hooked up ten and gnd with a paperclip, made sure its a solid connection, and hooked up ten to the negative battery. The check engine light stays on solid.

Any help would be greatly appreciated. I'm worried I should be billed more than my membership fee for the amount of help I need lol.

Andy kay93
Full Member
Posts: 237
Joined: Sun Apr 14, 2019 3:19 pm

Re: Check engine light on solid

Post by Andy kay93 » Fri Sep 20, 2019 11:14 pm

Hi where about are you, I’ve got a bit of diagnostic kit
Which might help, I’m in Manchester
Andy k

MikeyG
Full Member
Posts: 93
Joined: Thu Nov 29, 2018 6:01 pm
Has thanked: 1 time

Re: Check engine light on solid

Post by MikeyG » Fri Sep 20, 2019 11:25 pm

Hey up in Scotland (Dundee) unfortunately. :(

Andy kay93
Full Member
Posts: 237
Joined: Sun Apr 14, 2019 3:19 pm

Re: Check engine light on solid

Post by Andy kay93 » Fri Sep 20, 2019 11:29 pm

Shame, a bit far that 😐

MikeyG
Full Member
Posts: 93
Joined: Thu Nov 29, 2018 6:01 pm
Has thanked: 1 time

Re: Check engine light on solid

Post by MikeyG » Fri Sep 20, 2019 11:46 pm

What kind of tool is it? It seems I fix one thing and break three others in the process :(

Slick
Full Member
Posts: 821
Joined: Fri Sep 07, 2018 4:07 pm
Been thanked: 12 times

Re: Check engine light on solid

Post by Slick » Fri Sep 20, 2019 11:53 pm

Are the bypass connections right?
Engine with cross through it is usually alternator/battery related...

MikeyG
Full Member
Posts: 93
Joined: Thu Nov 29, 2018 6:01 pm
Has thanked: 1 time

Re: Check engine light on solid

Post by MikeyG » Fri Sep 20, 2019 11:57 pm

Its the engine with a cross through it, the battery has gone flat due it to being sitting there for a few months - I charged the battery all day before giving it a boot.

The engine with a cross through it is the check engine light right? Am I stupid as heck?

cpt black
Tech Rep
Posts: 2663
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 10 times
Been thanked: 82 times

Re: Check engine light on solid

Post by cpt black » Sat Sep 21, 2019 5:18 am

It certainly is usually means its the alternator faulty,if you have a volt meter
put across the battery terminals and you should get a reading of appx 14v
when running if the alternator is ok
But check the wiring if you pull the Moby back out and dos,nt work as only
3 circuit,s
Fuel pump
Starter
Dissy

MikeyG
Full Member
Posts: 93
Joined: Thu Nov 29, 2018 6:01 pm
Has thanked: 1 time

Re: Check engine light on solid

Post by MikeyG » Sun Sep 22, 2019 12:01 am

Changed the battery to a known good one and still doesn't start. Is there a way to test the alternator without the car being on?

Any help on how to read the engine code would be most helpful.

MikeyG
Full Member
Posts: 93
Joined: Thu Nov 29, 2018 6:01 pm
Has thanked: 1 time

Re: Check engine light on solid

Post by MikeyG » Sun Apr 05, 2020 11:54 pm

Hey guys,

Just gone back to it and the check engine light is still on. (Was hoping it might just magically turn itself off.)

I've connected the GND and TEN in the diagnostics bitty and nothing happens. I attached an LED to the B+ and FEN and it went on for about a second when I moved the key to the 2nd place (ON) then went out.

I dont think it happened when I was disconnecting the immobilizer - I shorted it with paperclips and have since removed them and just put the original connector back into the black box.

The car isn't starting either.

Not a lot to go on, but I really just wish I could read engine codes so that I could actually work out whats going wrong. Could the GND terminal in the diagnostics box be iffy as I was having problems reading the ABS codes previously.

Any help greatly appreciated.

Post Reply

Who is online

Users browsing this forum: No registered users and 36 guests